Cold Rooms / Commercial
Commercial Cold Room Manufacturer for Hotels, Restaurants, Retail and Cloud Kitchens
Commercial cold rooms are the workhorse refrigeration assets behind every hotel, cloud kitchen, supermarket and quick-service restaurant. HyperCold builds commercial cold rooms in chiller and freezer configurations, sized for SKU-rich kitchens and high-traffic retail back-stores.
We engineer for door-opening frequency, peak service-hour load and 24×7 reliability — the realities that make commercial cold rooms behave differently from agriculture or pharma rooms.
- Hotel, restaurant, cloud kitchen and retail builds
- Chiller + freezer twin rooms with shared anteroom
- High door-cycle hardware and air-curtain options
- Daikin OEM refrigeration with low-noise condensers
- Stainless racks, LED lighting, safety release inside door
- AMC tier specifically for HORECA uptime
Typical applications
Operating Temperature
+8°C to -25°C
Relative Humidity
70–90%
Engineering note
Commercial rooms are typically twin-room — chiller (+2°C to +4°C) for fresh, freezer (-18°C to -22°C) for frozen, served by a common anteroom.
Technical Specifications & Construction
Every commercial cold room we build follows the same engineering discipline — sized to your load, not picked off a brochure. Specifications below reflect typical HyperCold builds.
- PUF panel density
- 40 ± 2 kg/m³ (CFC-free polyurethane)
- Panel thickness (chiller)
- 80 mm or 100 mm
- Panel thickness (freezer)
- 125 mm or 150 mm
- Skin
- 0.5 mm PPGL / GI pre-coated steel both sides
- Joinery
- Cam-lock with EPDM gaskets
- Floor
- PUF + chequered Al / heated floor for freezers
- Refrigeration
- Daikin / Bitzer / Emerson scroll or screw
- Refrigerant
- R-404A / R-449A / R-507 as per BIS & MoEF norms
- Controls
- Carel / Danfoss digital with data-logger
- Door
- Hinged / sliding insulated + safety release
How HyperCold Designs This Cold Room
These are the design factors we lock down before quoting. Skip any of these and the project either runs hot, drinks electricity, or under-delivers on shelf life.
Product-specific temperature & humidity
We design from the commodity's psychrometric envelope, not a generic chiller spec. Different storage life targets get different design points.
Humidity & moisture control
Coil sizing, defrost strategy and air-throw decide whether your product dries out, sweats, or holds quality.
Air change rate & throw pattern
Velocity through the stack governs uniform pull-down. We engineer 25–60 ACH per room volume, not a default.
Refrigeration sizing on actual load
Heat load is calculated from product, infiltration, lighting, defrost, motor and personnel — never a TR/MT thumb rule.
Panel selection by ambient
100 mm in moderate zones, 150 mm in Rajasthan / interior MH. Panel density never below 40 kg/m³.
Serviceable layout & AMC access
Compressor decks, drain lines and electrical panels laid out for one-hand servicing — saves cost over 10 years.
What Drives the Project Cost
We don't quote square-foot rates — every build is BOQ-priced. The factors below decide where your project lands within a realistic range.
- 01Internal volume in CFT and storage tonnage
- 02Target temperature band (chiller, freezer, sub-zero, deep-freeze)
- 03PUF panel thickness and density
- 04Refrigeration capacity (TR) and compressor brand
- 05Daily product load and door-opening frequency
- 06Insulation upgrades for Tier-2 / hot-climate sites
- 07Civil work, levelling, drainage and trenching
- 08Electrical infrastructure, DG backup and stabilisation
- 09Automation level — basic, IoT-enabled, or SCADA
- 10Installation distance from Sirsaganj base and site access
- 11GST and statutory inclusions (toggled in BOQ)
- 12AMC tier — Standard, Pro, or 24×7 Critical
Why Operators Choose HyperCold
Built for door cycling
Hinge counts, gaskets, air-curtains and pull-down recovery are sized for 100+ door openings per day.
Low-noise condensers
Daikin and Bitzer condensing units with sound-attenuated options for rooftop install in city locations.
Service-grade interior
SS-304 floor option, IP-rated LEDs, drain heaters, internal safety release — built for kitchen use.
HORECA-grade AMC
Same-day response SLA in metro cities; spare-parts kit pre-stocked at multi-site clients.
Frequently Asked Questions
Subsidies & finance that may apply
Eligibility depends on project type, applicant category, state and current government notification. Below is indicative — verify with the official scheme portal before applying.
MIDH (State Horticulture Mission)
Credit-linked back-ended capital assistance for horticulture cold storage and pack houses.
Read scheme detailsNHB Cold Storage Subsidy
National Horticulture Board capital subsidy for cold storage and CA storage projects.
Read scheme detailsMoFPI Integrated Cold Chain (PMKSY)
Grant-in-aid for integrated pre-cooling, IQF, blast freezing, CA and reefer logistics.
Read scheme detailsAgriculture Infrastructure Fund (AIF)
Interest subvention and credit guarantee on bank term loans for post-harvest infrastructure.
Read scheme detailsPMFME — Micro Food Processing
Credit-linked subsidy for micro food processing units including small cold rooms.
Read scheme detailsState Subsidy Schemes
State Horticulture, Food Processing, SC/ST and SHG components vary by state action plan.
Read scheme detailsMSME & Bank Finance (CGTMSE, SIDBI, NABARD)
Term loan and working capital options via scheduled banks, SIDBI, NABARD and cooperatives.
Read scheme detailsReady to scope your commercial cold room?
Share your product, room size, and target temperature. We'll send a BOQ-priced quote with PUF, refrigeration, installation, and AMC — pan-India delivery from Sirsaganj, Firozabad.